Hillrom Compella Скачать руководство пользователя страница 67

Страница: 67 / 116

SideCom® Communication System

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

Press the

Enable

key until its indicator is on solid.

Press and release the

Volume

control until the indicator that is next to the

desired volume setting comes on.

HANGE

THE

LERT

ONE

NOTE:

We recommend that you use the same tone on all beds of a particular unit or floor, and do not change
the tone without facility authorization.

Activate one of Bed Exit modes. It is recommended to use another caregiver instead of a patient to
activate the Bed Exit mode.

NOTE:

To activate a Bed Exit mode, a minimum of 113 kg (250 lb) must be on the bed.

Activate the alert by having the caregiver exit the bed.

Press and hold the Volume control.

While you press the Volume control, press the Out-of-Bed control.

Press and release the Out-of-Bed control until the desired tone is reached.

Clear the alert condition.

SIDECOM® COMMUNICATION SYSTEM

URSE

ALL

ONTROL

A Nurse Call control is on the caregiver and patient control panels and the
patient pendant (if installed).

When a Nurse Call control is activated, a signal is sent to the nurses’
station. Voice communication is provided through a speaker/microphone
that is on the inside of both head-end siderails.

The SideCom® Communication System provides a control
for Nurse Call.

The SideCom® Communication System connector is on the
left side of the bed at the head end.

SideCom Connector

Patient

Control

Caregiver

Control

Содержание Compella





















































































































Результаты поиска

Содержание Compella

Отзывы:

Бренды по названию

Популярные бренды

Hillrom Compella, Инструкция по эксплуатации

Результаты поиска

Содержание Compella

Отзывы:

Бренды по названию

Популярные бренды