Hillrom Compella Скачать руководство пользователя страница 60

Страница: 60 / 116

Scale Systems

Compella™ Bariatric Bed System Instructions for Use (178951 REV 6)

Scale Reference Position

WARNING:

Warning

—Before you weigh the patient or zero the scale, make sure the bed is in the

Scale Reference

position

as defined below. Failure to do so could cause an inaccurate weight reading; patient injury

could occur.

If you attempt to

zero

the scale when the bed is not in the

Scale Reference

position

, you will hear a

triple beep to let you know that the bed is not in the correct position. Look for a flashing

Frame Setup

Release Brake

indicator. Repeat step 1 or 2 as identified by the flashing indicator.

NOTE:

If the

Brake Not Set alert

is sounding, you

will not

hear the triple beep, so we recommend that you

release the brake last.

The scale system is now ready for you to zero the scale or weigh the patient.

Press and hold the

Frame Setup

control until you hear a single beep. These will

occur:

The head section will flatten.

The foot section will fully lengthen.

The bed will lower to its lowest position.

Release the brake. The

Brake Not Set

alert will sound, so we recommend that you

do this step last to minimize the alert sound.

When the bed is correctly in the Scale Reference position, the

Scale Reference

indicator

will come on solid.

Содержание Compella





















































































































Результаты поиска

Содержание Compella

Отзывы:

Бренды по названию

Популярные бренды

Hillrom Compella, Инструкция по эксплуатации

Результаты поиска

Содержание Compella

Отзывы:

Бренды по названию

Популярные бренды