Hill-Rom WatchCare Series Скачать руководство пользователя страница 21

Страница: 21 / 74

WatchCare™ Incontinence Management System User and Service Manual (196414 REV 2)

Cleaning and Disinfecting

Table 1 below summarizes the approved cleaners/disinfectants for use
with the associated contact time for disinfection.

Table 1: Approved Cleaners/Disinfectants

*Bleach is not recommended as the primary cleaner/disinfectant.

Remove any disinfectant residue prior to and after the use of bleach

with a new or clean cloth/wipe soaked in tap water.

When you perform the detailed cleaning steps, please note the following:

•

A microfiber cloth or the Clorox HealthCare® Bleach Germicidal
Wipe is recommended as the wiping cloth

•

Always replace the wiping cloth when visibly soiled.

•

Always replace the wiping cloth between steps (spot clean, clean,
and disinfect).

•

Always use Personal Protective Equipment (PPE).

Prepare for Cleaning and Disinfecting

Unplug the bed.

Cleaner/
Disinfectant

Recommended
for Routine
Cleaning and
Disinfection

Recommended
for Disinfection
against
Clostridium
Difficile (C.Diff)

Maintain
Wetness
(Disinfection
Contact Time)

Wex-Cide™ Ger-
micidal Deter-
gent ready-to-
use

Yes

10 minutes

Virex® II 256

Yes

10 minutes

OxyCide® Daily
Disinfectant
Cleaner

Yes

3 minutes

Clorox Health-
Care® Bleach
Germicidal
Cleaner ready-
to-use

Yes

5 minutes

Clorox Health-
Care® Bleach
Germicidal
Wipes

Yes

3 minutes

DRAFT 26-FEB-2019

Содержание WatchCare Series











































































Результаты поиска

Содержание WatchCare Series

Отзывы:

Hill-Rom WatchCare Series, Руководство пользователя и обслуживания, Страница: 21 / 74

Результаты поиска

Содержание WatchCare Series

Отзывы: