manualshive.com logo in svg

Hill-Rom P870, Руководство пользователя

Поделиться
Скачать
Hill-Rom P870 Скачать руководство пользователя страница 39

Resident

TM

 LTC Electric Drive Bed Specifications

Chapter 1: Introduction

Page 1 - 26

Resident

TM

 LTC Bed Service Manual (man136rc)

1

The control box lockout is located at the foot end of the bed. The position of 
each control knob on the control lockout is pictorially labeled to indicate each 
governing function and the locked/unlocked position. See “Automatic 
Contour” on page 1-22.

Motor Actuators

There are three separate motor actuators which provide hilow, head, and knee 
operation. Each is built to withstand the common hazards of spills and cleaning 
liquids under normal conditions. These motor actuators are a plug-in design for 
easy removal in the event of problems. Each is specially designed for its 
individual function and has the following characteristics:

• 24 volt, DC motor

• Electronic overload protection, microswitch motor cutoff

• Totally enclosed, impact resistant motor housing

• Permanently lubricated

• Precision-rolled acme spindle for linear actuation of stainless steel piston

• Heavy-duty ball bearing spindle mount

• Flexible clutch drive to reduce vibration and noise

NOTE:
The battery pack accessory can provide emergency operation of the actuators 
to position the bed in event of a power failure.

Specifications for these motor actuators are as follows:

Hilow

• 12.60" (32.0 cm) actuator stroke

• 20 1/4" (51.4 cm) retracted length

Head

• 7 1/4" (18.4 cm) actuator stroke

• 46.38" (117.8 cm) retracted length

Knee

• 2.88" (7.3 cm) actuator stroke

• 39 1/4" (99.7 cm) retracted length

Содержание P870








































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды