Hill-Rom P870 Скачать руководство пользователя страница 134

Страница: 134 / 231

4.8 Optional Siderail Control Panels

Chapter 4: Removal, Replacement, and Adjustment Procedures

Resident

LTC Bed Service Manual (man136rc)

Page 4 - 27

4.8

Optional Siderail Control Panels

Tools required:

Phillips head screwdriver

T25 torx head screwdriver

Diagonal cutters

Removal

1. Unplug the bed from its power source.

SHOCK HAZARD:

Unplug the bed from its power source. An electrical shock hazard
exists.

2. Disconnect the siderail control cable from connection (A) at the control

lockout box (see figure 4-21 on page 4-27).

Figure 4-21. Location Of Siderail Control Cable Connections At Control Lockout

NOTE:
Record the cable routing and placement of cable ties for replacement purposes.

3. Remove the attached cable ties.

4. Carefully peel the hilow label (A) from the outer surface of the siderail

control (R) and the head/seat label (I) from the inner surface of the control
(G) (see figure 4-22 on page 4-28).

CAUTION:

Use care when removing the siderail labels to prevent damage.
Replace damaged labels with new ones.

m136_068

Содержание P870








































































































































































































































Результаты поиска

Содержание P870

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom P870, Руководство пользователя

Результаты поиска

Содержание P870

Отзывы:

Бренды по названию

Популярные бренды