Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 99

Страница: 99 / 220

4.11 Gas Display Board

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 36

CarePorter™ Cart Service Manual (man239)

Figure 4-13. Gas Display Board Removal

6. Carefully lift up the top cover assembly (B) to expose the gas display board

(C).

7. Carefully disconnect the gas display cable (D) from the gas display board

(C).

8. Using the phillips head screwdriver, remove the four screws (E) that secure

the gas display board (C) to the top cover assembly (B).

Replacement

To install the replacement gas display board (C), reverse the removal
procedure.

Adjustment

No adjustment is required for the gas display board (C).

m239_050

Содержание CarePorter P3000





























































































































































































































Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Результаты поиска

Содержание CarePorter P3000

Отзывы:

Бренды по названию

Популярные бренды