manualshive.com logo in svg

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Поделиться
Скачать
Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 27

Safety Tips

Chapter 1: Introduction

Page 1 - 14

CarePorter™ Cart Service Manual (man239)

WARNING:

Ensure the IV pole does not slip downward during the removal 
procedure. Failure to do so could result in personal injury or equipment 
damage.

CAUTION:

Ensure that there is proper clearance for the IV poles when operating 
the CarePorter™ Cart in a patient's room. Failure to do so could result 
in equipment damage.

Power Equipment Shelf

WARNING:

Ensure the power equipment shelf is rotated 90º before docking the cart 
to the bed/stretcher. Failure to do so could result in personal injury or 
equipment damage.

Rotate the power equipment shelf 90º before docking the cart to the 
bed/stretcher.

WARNING:

Ensure that all hoses, power cords, and connections are oriented 
correctly and properly connected. Failure to position the ventilator 
correctly may result in crimping or kinking of the hoses. Possible 
personal injury or equipment damage could occur.

Before transporting the patient, inspect all hoses and connections. The 
ventilator hoses may become crimped if the ventilator is not positioned 
properly under the bed.

Содержание CarePorter P3000





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды