manualshive.com logo in svg

Hill-Rom CarePorter P3000, Руководство по обслуживанию

Поделиться
Скачать
Hill-Rom CarePorter P3000 Скачать руководство пользователя страница 25

Safety Tips

Chapter 1: Introduction

Page 1 - 12

CarePorter™ Cart Service Manual (man239)

Safety Tips

Operating Precautions

General Operation

WARNING:

Do not raise and lower the bed or stretcher when the CarePorter™ Cart 
is attached. Possible personal injury or equipment damage could occur.

WARNING:

The weight of the bed or stretcher with a patient and the CarePorter™ 
Cart attached could exceed 1200 lb (544 kg). Ensure that you maintain 
control during transport of the CarePorter™ Cart. Failure to do so could 
result in personal injury or equipment damage.

WARNING:

When the CarePorter™ Cart is stationary, ensure the brakes are set. 
Failure to do so could result in personal injury or equipment damage.

WARNING:

Do not raise or lower the power equipment shelf when the CarePorter™ 
Cart is attached to the bed. Doing so could result in personal injury or 
equipment damage.

WARNING:

Ensure the bracket weldment is fully seated into the ISS socket before 
using the monitor/equipment shelf. Failure to do so could result in 
personal injury or equipment damage.

CAUTION:

Ensure the bracket weldment is fully seated into the ISS socket before 
using the ventilator display mount. Failure to do so could result in 
personal injury or equipment damage.

Содержание CarePorter P3000





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды