Hill-Rom 305 Manual Bed страница 77 Скачать руководство пользователя

Страница: 77 / 176

4.11 Hilow Motor

Chapter 4: Removal, Replacement, and Adjustment Procedures

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 4 - 25

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

4.11 Hilow Motor

Tools required:

10 mm hex wrench

13 mm socket

Needle nose pliers

Wire cutters

Bed supports

Removal

WARNING:

Do not work under an unsupported load. Install appropriate temporary
supports. Failure to do so could cause injury or equipment damage.

1. Put bed supports under the upper bed frame.

2. Disconnect the battery cable from the control board (refer to procedure 4.7

on page 4-16).

3. Raise the head section (A) to its highest position (see figure 4-11 on page

4-26).

SHOCK HAZARD:

Disconnect the bed from its power source. Failure to do so could cause
injury or equipment damage.

4. Disconnect the bed from its power source.

5. Make a note that shows how the cable routes from the hilow motor (B) to

the control box assembly (C).

CAUTION:

Use caution when you cut the wire ties. Failure to do so could cause
cable damage.

6. Carefully cut all of the wires ties that attach the hilow motor cable (D) to

the bed frame (E).

7. Disconnect the hilow motor cable (D) from the control box assembly (C).

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды

Hill-Rom 305 Manual Bed, Руководство по обслуживанию

Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды