HIKVISION iDS-8104AHQXLI-E4 Скачать руководство пользователя страница 195

Страница: 195 / 224

ATM Digital Video Recorder User Manual

194

Step 4

You can click the

Pause

button to pause the detection and click the

Resume

button to

resume the detection.

Step 5

If there is error information about the HDD, you can click the

Error Info

button to view the

information.

13.8 Configuring HDD Error Alarms

Purpose

You can configure the HDD error alarms when the HDD status is

Uninitialized

Abnormal

Step 1

Enter the Exception interface.

Menu > Configuration > Exceptions

Step 2

Select the Exception Type to

HDD Error

from the drop-down list.

Step 3

Check the checkbox(s) below to select the linkage action(s) for HDD error, as shown in
Figure 13-22.

The linkage actions can be selected to: Audible Warning, Notify Surveillance Center, Send
Email and Trigger Alarm Output.

Figure 13-22

Configure HDD Error Alarm

Step 4

When the

Trigger Alarm Output

is selected, you can also select the alarm output to be

triggered from the list below.

Step 5

Click the

Apply

button to save the settings.

Содержание iDS-8104AHQXLI-E4

































































































































































































































Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды

HIKVISION iDS-8104AHQXLI-E4, Руководство пользователя

Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды