HIKVISION iDS-8104AHQXLI-E4 Скачать руководство пользователя страница 191

Страница: 191 / 224

ATM Digital Video Recorder User Manual

190

Figure 13-15

Set HDD Property

Step 3

Set the HDD property to R/W, Read-only or Redundancy.

Step 4

Click the

button to save the settings and exit the interface.

Step 5

In the HDD Information menu, the HDD property will be displayed in the list.

At least 2 hard disks must be added on your DVR when you want to set a HDD to Redundancy, and
there is one HDD with R/W property.

13.4 Configuring Quota Mode

Purpose

Each camera can be configured with allocated quota for the storage of recorded files.

Steps

Step 1

Enter the

Storage Mode

interface.

Menu > HDD > Advanced

Step 2

Click the

Storage Mode

tab.

Step 3

Set the

Mode

to Quota, as shown in Figure 13-16.

The DVR must be rebooted to enable the changes to take effect.

Содержание iDS-8104AHQXLI-E4

































































































































































































































Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

HIKVISION iDS-8104AHQXLI-E4, Руководство пользователя, Страница: 191 / 224

Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы: