HIKVISION iDS-8104AHQXLI-E4 Скачать руководство пользователя страница 183

Страница: 183 / 224

ATM Digital Video Recorder User Manual

182

Step 1

Enter the Array Settings interface. The disk 3 is lost.

Menu > HDD > RAID > Array

Figure 12-13

Array Settings Interface

Step 2

Click Array tab to return to the Array Settings interface and click

to configure the array

rebuild.

At least one available physical disk should exist for rebuilding the array.

Figure 12-14

Rebuild Array Interface

Step 3

Select the available physical disk and click OK button to confirm to rebuild the array.

Step 4

The “Do not unplug the physical disk when it is under rebuilding” message box pops up.
Click OK button to start rebuilding.

Step 5

You can enter the Array Settings interface to view the rebuilding status.

Step 6

After rebuilding successfully, the array and virtual disk will restore to Functional.

12.3 Deleting Array

Deleting array will cause to delete all the data saved in the disk.

Step 1

Enter the Array Settings interface.

Menu>HDD>RAID>Array

Содержание iDS-8104AHQXLI-E4

































































































































































































































Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды

HIKVISION iDS-8104AHQXLI-E4, Руководство пользователя

Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды