HIKVISION iDS-8104AHQXLI-E4 Скачать руководство пользователя страница 128

Страница: 128 / 224

ATM Digital Video Recorder User Manual

127

Select one day of a week and up to eight time periods can be set within each day. Or you
can click

Copy

to copy the time period settings to other day(s).

Time periods shall not be repeated or overlapped.

Figure 8-14

Set Arming Schedule of Video Quality Diagnostics

Select

Linkage Action

tab to set alarm response actions of video quality diagnostics alarm

(Refer to

Chapter

8.7 Setting Alarm Response Actions

Click

to complete the video quality diagnostics settings of the channel.

Step 6

Repeat the above steps to finish settings of other channels, or click

Copy

to copy the above

settings to them.

Step 7

Click

Apply

to save the settings.

8.6 Handling Exceptions

Purpose

Exception settings refer to the handling method of various exceptions, e.g.



HDD Full:

The HDD is full.



HDD Error:

Writing HDD error, unformatted HDD, etc.



Network Disconnected:

Disconnected network cable.



IP Conflicted:

Duplicated IP address.



Illegal Login:

Incorrect user ID or password.



Input/Recording Resolution Mismatch:

The input resolution is smaller than the recording

resolution.

Содержание iDS-8104AHQXLI-E4

































































































































































































































Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды

HIKVISION iDS-8104AHQXLI-E4, Руководство пользователя

Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды