HIKVISION iDS-8104AHQXLI-E4 Скачать руководство пользователя страница 120

Страница: 120 / 224

ATM Digital Video Recorder User Manual

119

Chapter 8 Alarm Settings

8.1 Setting Motion Detection

Step 1

Enter

Motion Detection

interface of Camera Management.

Menu> Camera> Motion

Figure 8-1

Motion Detection Setup Interface

Step 2

Select a camera you want to set up motion detection.

Step 3

Check

checkbox to enable motion detection.

Step 4

Set detection area and sensitivity.

Use the mouse to draw detection area(s) or click

Full Screen

to set the detection area to be

the full screen and drag the sensitivity bar to set sensitivity.

Figure 8-2

Set Detection Area and Sensitivity

Step 5

Click

to set alarm response actions.

Содержание iDS-8104AHQXLI-E4

































































































































































































































Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды

HIKVISION iDS-8104AHQXLI-E4, Руководство пользователя

Результаты поиска

Содержание iDS-8104AHQXLI-E4

Отзывы:

Похожие инструкции для iDS-8104AHQXLI-E4

Бренды по названию

Популярные бренды