HIKVISION HiWatch HWI-B120H-U Скачать руководство пользователя

Страница: 78 / 193

Network Camera User Manual

Note:

WebSocket and WebSockets protocol are used for plug-in free live view. For

detailed information, see

7.2.11.

Click

Save

to save the settings.

Note:

A reboot is required for the settings to take effect.

Configure NAT (Network Address Translation) Settings

Purpose:

NAT interface allows you to configure the UPnP™ parameters.

Universal Plug and Play (UPnP™) is a networking architecture that provides

compatibility among networking equipment, software and other hardware devices.

The UPnP protocol allows devices to connect seamlessly and to simplify the

implementation of networks in the home and corporate environments.

With the function enabled, you don’t need to configure the port mapping for each port,

and the camera is connected to the Wide Area Network via the router.

UPnP Settings

Steps:

Enter the NAT settings interface.

Configuration > Network > Basic Settings >

NAT.

Check the checkbox to enable the UPnP™ function.

Note:

Only when the UPnP™ function is enabled, ports of the camera are active.

Содержание HiWatch HWI-B120H-U


































































































































































































Результаты поиска

Содержание HiWatch HWI-B120H-U

Отзывы:

Похожие инструкции для HiWatch HWI-B120H-U

Бренды по названию

Популярные бренды

HIKVISION HiWatch HWI-B120H-U, Руководство пользователя

Результаты поиска

Содержание HiWatch HWI-B120H-U

Отзывы:

Похожие инструкции для HiWatch HWI-B120H-U

Бренды по названию

Популярные бренды