HIKVISION HiWatch HWI-B120H-U Скачать руководство пользователя

Страница: 188 / 193

Network Camera User Manual

187

Appendix

Appendix 1 SADP Software Introduction



Description of SADP

SADP (Search Active Devices Protocol) is a kind of user-friendly and installation-free

online device search tool. It searches the active online devices within your subnet and

displays the information of the devices. You can also modify the basic network

information of the devices using this software.



Search active devices online



Search online devices automatically

After launch the SADP software, it automatically searches the online devices

every 15 seconds from the subnet where your computer locates. It displays the

total number and information of the searched devices in the Online Devices

interface. Device information including the device type, IP address and port

number, etc. will be displayed.

Figure A.1.1 Searching Online Devices

Note:

Device can be searched and displayed in the list in 15 seconds after it went

online; it will be removed from the list in 45 seconds after it went offline.

Содержание HiWatch HWI-B120H-U


































































































































































































Результаты поиска

Содержание HiWatch HWI-B120H-U

Отзывы:

Похожие инструкции для HiWatch HWI-B120H-U

Бренды по названию

Популярные бренды

HIKVISION HiWatch HWI-B120H-U, Руководство пользователя

Результаты поиска

Содержание HiWatch HWI-B120H-U

Отзывы:

Похожие инструкции для HiWatch HWI-B120H-U

Бренды по названию

Популярные бренды