HIKVISION DS-K3B631TX Series Скачать руководство пользователя страница 28

Страница: 28 / 174

Chapter 5 General Wiring

Note

●

When you should maintain or disassemble the high voltage modules, you should remove the

entire high voltage modules and maintain it outside the turnstile. You should unplug the cables

that connected to the peripherals before maintenance to avoid destroy of the device.

●

When disassembling the high voltage module, you should disconnect the power to avoid injury.

●

If only wiring is needed without maintenance, do not remove the high voltage modules.

●

The switch and the main lane control board are already connected. The 14 AWG cable to

connect between the AC electric supply and the switch should be purchased separately.

●

2 interconnecting cables are supplied: 24 V Power Cable and Communication Cable.

24 V Power Cable: 4 m long, which is in the middle and right pedestal.

Communication Cable: 4 m long, CAT5e, which is in the package of middle and right pedestal.

5.1 Components Introduction

By default, basic components of the turnstile are connected well. The pedestals can communicate

by wiring the interconnecting cables. And the turnstile supports wiring the AC electric supply for

the whole system's power supply.

Note

The voltage fluctuation of the electric supply is between 100 VAC and 260 VAC, 50 to 60 Hz.

The picture displayed below describes each component's position on the turnstile.

Note

The diagram is for reference only.

DS-K3B631TX Series Swing Barrier User Manual

Содержание DS-K3B631TX Series















































































































































































Результаты поиска

Содержание DS-K3B631TX Series

Отзывы:

Похожие инструкции для DS-K3B631TX Series

Бренды по названию

Популярные бренды

HIKVISION DS-K3B631TX Series, Руководство пользователя

Результаты поиска

Содержание DS-K3B631TX Series

Отзывы:

Похожие инструкции для DS-K3B631TX Series

Бренды по названию

Популярные бренды