HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 47

Страница: 47 / 243

User Manual of Network Video Recorder User Manual

3.3

Adjusting Live View Settings

Purpose:

Live View settings can be customized according to different needs. You can configure the output interface, dwell

time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.

Steps:

Enter the Live View Settings interface.

Menu> Configuration> Live View

Figure 3. 7

Live View-General

The settings available in this menu include:

•

Video Output Interface:

Designates the output to configure the settings for. Selectable outputs include

VGA/HDMI and VGA2/HDMI2.

•

Live View Mode:

Designates the display mode to be used for Live View.

•

Dwell Time:

The time in seconds to

dwell

between switching of channels when enabling auto-switch in Live

View.

•

Enable Audio Output:

Enables/disables audio output for the selected video output.

•

Volume:

Adjust the volume of live view, playback and two-way audio for the selected output interface.

•

Event Output:

Designates the output to show event video.

•

Full Screen Monitoring Dwell Time:

The time in seconds to show alarm event screen.

Setting Cameras Order

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 47 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: