HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 22

Страница: 22 / 243

User Manual of Network Video Recorder User Manual

1.5

Rear Panel

Figure 1. 5

Rear Panel

Table 1. 5

Description of Rear Panel Interfaces

No.

Item

Description

LAN1/LAN2 Interface

2 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interfaces provided.

LINE IN

RCA connector for audio input.

AUDIO OUT

2 RCA connectors for audio output.

HDMI1/HDMI2

HDMI video output connector.

VGA1/VGA2

DB9 connector for VGA output. Display local video output and menu.

USB 3.0 interface

Universal Serial Bus (USB) ports for additional devices such as USB

mouse and USB Hard Disk Drive (HDD).

RS-232 Interface

Connector for RS-232 devices.

eSATA

Connects external SATA HDD, CD/DVD-RM.

Controller Port

D+, D- pin connects to Ta, Tb pin of controller. For cascading devices,

the first NVR’s D+, D- pin should be connected with the D+, D- pin of

the next NVR.

ALARM IN

Connector for alarm input.

ALARM OUT

Connector for alarm output.

AC 100V ~ 240V

100V ~ 240 VAC power supply.

Power Switch

Switch for turning on/off the device.

GROUND

Ground (needs to be connected when NVR starts up).

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 22 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: