HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 157

Страница: 157 / 243

User Manual of Network Video Recorder User Manual

156

alarm is triggered. The remote alarm host must have the Network Video Surveillance software installed.

Steps:

Enter the Network Settings interface.

Menu >Configuration> Network

Select the

More Settings

tab to enter the More Settings interface, as shown in Figure 11. 15.

Figure 11. 15

More Settings Interface

Enter

Alarm Host IP

and

Alarm Host Port

in the text fields.

The

Alarm Host IP

refers to the IP address of the remote PC on which the Network Video Surveillance

Software (e.g., iVMS-4200) is installed, and the

Alarm Host Port

must be the same as the alarm monitoring

port configured in the software.

Click the

Apply

button to save and exit the interface.

11.2.6

Configuring Multicast

Purpose:

The multicast can be configured to realize live view for more than 128 connections through network for the device.

A multicast address spans the Class-D IP range of 224.0.0.0 to239.255.255.255. It is recommended to use the IP

address ranging from 239.252.0.0 to 239.255.255.255.

Steps:

Enter the Network Settings interface.

Menu >Configuration> Network

Select the

More Settings

tab to enter the More Settings interface, as shown in Figure 11. 15.

Set

Multicast IP

, as shown in Figure 11. 16. When adding a device to the Network Video Surveillance

Software, the multicast address must be the same as the NVR’s multicast IP.

Figure 11. 16

Configure Multicast

Click the

Apply

button to save and exit the interface.

The multicast function should be supported by the network switch to which the NVR is connected.

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 157 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: