HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 215

Страница: 215 / 243

User Manual of Network Video Recorder User Manual

214

16.1

Configuring RS-232 Serial Port

Purpose:

The RS-232 port can be used in two ways:

•

Parameters Configuration: Connect a PC to the NVR through the PC serial port. Device parameters can be

configured by using software such as HyperTerminal. The serial port parameters must be the same as the

NVR’s when connecting with the PC serial port.

•

Transparent Channel: Connect a serial device directly to the NVR. The serial device will be controlled

remotely by the PC through the network and the protocol of the serial device.

Steps:

Enter the RS-232 Settings interface.

Menu >Configuration> RS-232

Figure 16. 1

RS-232 Settings Interface

Configure RS-232 parameters, including baud rate, data bit, stop bit, parity, flow control and usage.

Click the

Apply

button to save the settings.

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 215 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: