HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 189

Страница: 189 / 243

User Manual of Network Video Recorder User Manual

188

13.4

Managing HDD Group

13.4.1

Setting HDD Groups

Purpose:

Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD

group through HDD settings.

Steps:

Enter the Storage Mode interface.

Menu > HDD > Advanced > Storage Mode

Set the

Mode

to Group, as shown in Figure 13. 13.

Figure 13. 13

Storage Mode Interface

Click the

Apply

button and the following Attention box will pop up.

Figure 13. 14

Attention for Reboot

Click the

Yes

button to reboot the device to activate the changes.

After reboot of device, enter the HDD Information interface.

Menu > HDD> General

Select HDD from the list and click

icon to enter the Local HDD Settings interface, as shown in Figure

13. 15.

Figure 13. 15

Local HDD Settings Interface

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 189 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: