HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 184

Страница: 184 / 243

User Manual of Network Video Recorder User Manual

183

13.1

Initializing HDDs

Purpose:

A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR.

A message box pops up when the NVR starts up if there exits any uninitialized HDD.

Figure 13. 1

Message Box of Uninitialized HDD

Click

Yes

button to initialize it immediately or you can perform the following steps to initialize the HDD.

Steps:

Enter the HDD Information interface.

Menu > HDD> General

Figure 13. 2

HDD Information Interface

Select HDD to be initialized.

Click the

Init

button.

Figure 13. 3

Confirm Initialization

Select the

button to start initialization.

Figure 13. 4

Status changes to Initializing

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 184 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: