HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 173

Страница: 173 / 243

User Manual of Network Video Recorder User Manual

172

12.1

Configuring Array

Purpose:

RAID (redundant array of independent disks) is a storage technology that combines multiple disk drive

components into a logical unit. A RAID setup stores data over multiple hard disk drives to provide enough

redundancy so that data can be recovered if one disk fails. Data is distributed across the drives in one of several

ways called "RAID levels", depending on what level of redundancy and performance is required.

The NVR support the disk array which is realized by the software, and RAID0, RAID1, RAID5 and RAID 10 are

supported. You can enable the RAID function on your demand.

Before you start:

Please install the HDD(s) properly and it is recommended to use the same enterprise-level HDDs (including model

and capacity) for array creation and configuration so as to maintain reliable and stable running of the disks.

Introduction:

The NVR can store the data (such as record, picture, log information) in the HDD only after you have created the

array or you have configured network HDD (refer to

Chapter13.2 Managing Network HDD

). Our device provides

two ways for creating array, including one-touch configuration and manual configuration. The following flow

chart shows the process of creating array.

Figure 12. 1

RAID Working Flow

12.1.1

Enable RAID

Purpose:

Perform the following steps to enable the RAID function, or the disk array cannot be created.

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 173 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: