HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 16

Страница: 16 / 243

User Manual of Network Video Recorder User Manual

1.1

Front Panel

Figure 1. 1

Front Panel

Table 1. 1

Description of Control Panel Buttons

No.

Name

Function Description

Status

Indicators

ALARM

Turns red when a sensor alarm is detected.

READY

Turs blue when the device is functioning properly.

STATUS

Turns blue when device is controlled by an IR remote.

Turns red when controlled by a keyboard and purple when IR

remote and keyboard is used at the same time.

HDD

Flickers red when data is being read from or written to HDD.

MODEM

Reserved for future usage.

Tx/Rx

Flickers blue when network connection is functioning properly.

GUARD

Turns blue when the device is in armed status; at this time, an

alarm is enabled when an event is detected.

Turns off when the device is unarmed. The arm/disarm status

can be changed by pressing and holding on the ESC button for

more than 3 seconds in live view mode.

IR Receiver

Receiver for IR remote control.

Front Panel Lock

Locks or unlocks the panel by the key.

DVD-R/W

Slot for DVD-R/W disk.

Alphanumeric Buttons

Switches to the corresponding channel in live view or PTZ

control mode.

Inputs numbers and characters in edit mode.

Switches between different channels in playback mode.

Turns blue when the corresponding channel is recording; turns

red when the channel is in network transmission status; turns

pink when the channel is recording and transmitting.

USB Interfaces

Universal Serial Bus (USB) ports for additional devices such as

USB mouse and USB Hard Disk Drive (HDD).

Composite

Keys

ESC

Returns to the previous menu.

Presses for arming/disarming the device in live view mode.

REC/SHOT

Enters the Manual Record settings menu.

Presses this button followed by a numeric button to call a PTZ

preset in PTZ control settings.

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 16 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: