HIKVISION DS-9608NI-I8 Скачать руководство пользователя страница 108

Страница: 108 / 243

User Manual of Network Video Recorder User Manual

107

7.3

Hot Spare Device Backup

Purpose:

Several devices, including NVR and HDVR, can form an N+1 hot spare system. The system consists of several

working devices and a hot spare device; when the working device fails, the hot spare device switches into

operation, thus increasing the reliability of the system.

Please contact dealer for details of models which support the hot spare function.

Before you start:

At least 2 devices are online.

A bidirectional connection shown in the figure below is required to be built between the hot spare device and each

working device.

Set a hot spare

device

Add a hot spare

device on normal

device

Add the normal

device on the hot

spare device

Start

Finish

Figure 7. 13

Building Hot Spare System

7.3.1

Setting Hot Spare Device



The camera connection will be disabled when the device works in the hot spare mode.



It’s highly recommended

to restore the defaults of the device after switching the working mode of the hot

spare device to normal mode to ensure the normal operation afterwards.

Steps:

Enter the Hot Spare settings interface.

Menu > Configuration > Hot Spare

Set the Work Mode as Hot Spare Mode, click the

Apply

button to confirm the settings.

Reboot the device to make the change take effect.

Figure 7. 14

Reboot Attention

Click the

Yes

button in the pop-up attention box.

Содержание DS-9608NI-I8




















































































































































































































































Результаты поиска

Содержание DS-9608NI-I8

Отзывы:

HIKVISION DS-9608NI-I8, Руководство пользователя, Страница: 108 / 243

Результаты поиска

Содержание DS-9608NI-I8

Отзывы: