HIKVISION DS-7608NI-I2/8P Скачать руководство пользователя страница 77

Страница: 77 / 221

I Series Network Video Recorder User Manual, 030117NA

Select the HDD and click

to enter the Local HDD Settings interface.

Set the HDD property to Redundancy.

Figure 82 HDD General-Editing

Click Apply to save the settings.

Click OK to go back to the upper level menu.

NOTE:

You must set the Storage mode in the HDD advanced settings to Group before you set the HDD

property to Redundant. See

Chapter 11.4.1

Setting HDD Property. There should be at least another HDD that is in Read/Write status.

Enter the Record setting interface, Menu > Recording Configuration > Parameters

Select Record tab.

Click More Settings to enter the following interface.

Figure 83 Record Parameters

Содержание DS-7608NI-I2/8P






























































































































































































































Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы:

HIKVISION DS-7608NI-I2/8P, Руководство пользователя, Страница: 77 / 221

Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы: