HIKVISION DS-7608NI-I2/8P Скачать руководство пользователя страница 73

Страница: 73 / 221

I Series Network Video Recorder User Manual, 030117NA

Figure 74 Motion Detection Handling

Select the channels that you want the motion detection event to trigger recording.

Click

Apply

to save the settings.

Click

to go back to the upper level menu.

Exit the Motion Detection menu.

10.

Edit the Motion Detection Record Schedule. For the detailed information of schedule configuration, see

Configuring Recording and Capture Schedule.

6.4

Configuring Alarm Triggered Recording and Capture

Follow the procedure below to configure alarm triggered recording or capture.

Enter the Alarm settings interface, Menu > Recording Configuration > Alarm.

Figure 75 Alarm Settings

Содержание DS-7608NI-I2/8P






























































































































































































































Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы:

HIKVISION DS-7608NI-I2/8P, Руководство пользователя, Страница: 73 / 221

Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы: