HIKVISION DS-7608NI-I2/8P Скачать руководство пользователя страница 61

Страница: 61 / 221

I Series Network Video Recorder User Manual, 030117NA

Figure 56 PTZ Panel, General

Click the

Call Pattern

button to call it.

Click the

Stop Pattern

button to stop calling it.

5.2.8.

Customizing Linear Scan Limit

The Linear Scan can be enabled to trigger the scan in the horizantal direction in the predefined range.

NOTE:

This function is supported only by certain models.

Enter the PTZ Control interface, Menu > Camera > PTZ.

Figure 57 PTZ Settings

Use the directional button to wheel the camera to the location where you want to set the limit, and
click the

Left Limit

Right Limit

button to link the location to the corresponding limit.

NOTE:

The speed dome starts linear scan from the left limit to the right limit, and you must set the left limit on
the left side of the right limit. As well, the angle from the left limit to the right limit must be no more than
180

Содержание DS-7608NI-I2/8P






























































































































































































































Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы:

HIKVISION DS-7608NI-I2/8P, Руководство пользователя, Страница: 61 / 221

Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы: