HIKVISION DS-7608NI-I2/8P Скачать руководство пользователя страница 26

Страница: 26 / 221

I Series Network Video Recorder User Manual, 030117NA

2.5

DS-77xxNI-I4/16P Rear Panel

Figure 5 DS-77xxNI-I4/16P

Table 4 – Panel Description

No.

Name

Description

LAN Interface

1 network interface provided for DS-7700NI-I4/P.

AUDIO OUT

RCA connector for audio output

LINE IN

RCA connector for audio input

HDMI

HDMI video output connector

USB 3.0 interface

USB ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD)

RS-232 Interface

Connector for RS-232 devices

VGA

DB-15 connector for VGA output. Display local video output and menu.

RS-485 Interface

Half-duplex connector for RS-485 devices

ALARM IN

Connector for alarm input

ALARM OUT

Connector for alarm output

GROUND

Ground (needs to be connected when NVR starts up)

100 VAC to 240 VAC

100 to 240 VAC power supply

Power Switch

Switch for turning on/off the device

Network Interfaces with PoE function
(supported by DS-7700NI-I4/P)

Network interfaces for the cameras and to provide power over Ethernet

2.6

DS-76xxNI-I2/xP Series Rear Panels

Figure 6 DS-76xxNI-I2/8P

Figure 7 DS-7608NI-I2/16P

Содержание DS-7608NI-I2/8P






























































































































































































































Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы:

HIKVISION DS-7608NI-I2/8P, Руководство пользователя, Страница: 26 / 221

Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы: