HIKVISION DS-7608NI-I2/8P Скачать руководство пользователя страница 25

Страница: 25 / 221

I Series Network Video Recorder User Manual, 030117NA

2.3

DS-76xxNI-I2/xP Series Front Panel

Figure 3 DS-76xxNI-I2/xP Series

Table 3 – Panel Description

No.

Item

Description

On/Off Power

Turns green when device is on

Hard Drive

Flickers red when data is being read from or written to HDD

Network Tx/Rx

Flickers blue when network connection is functioning properly

USB Port

Connects USB mouse or USB flash memory devices

2.4

DS-96xxNI-I8 Series Rear Panel

Figure 4 DS-96xxNI-I8 Series

Table 3 – Panel Description

No.

Name

Description

LAN1/LAN2 Interface

2 RJ-45 10/100/1000 Mbps self-adaptive Ethernet interfaces provided.

LINE IN

RCA connector for audio input.

AUDIO OUT

2 RCA connectors for audio output.

HDMI1/HDMI2

HDMI video output connector.

VGA1/VGA2

DB-15 connector for VGA output. Display local video output and menu.

USB 3.0 interface

USB ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD).

RS-232 Interface

Connector for RS-232 devices.

eSATA

Connects external SATA HDD, CD/DVD-RM.

Controller Port

D+, D- pin connects to Ta, Tb pin of controller. For cascading devices, the first NVR’s D+, D- pin should
be connected with the D+, D- pin of the next NVR.

ALARM IN

Connector for alarm input.

ALARM OUT

Connector for alarm output.

100 to 240 VAC

100 to 240 VAC power supply.

Power Switch

Switch for turning on/off the device.

GROUND

Ground (needs to be connected when NVR starts up).

Содержание DS-7608NI-I2/8P






























































































































































































































Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы:

HIKVISION DS-7608NI-I2/8P, Руководство пользователя, Страница: 25 / 221

Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы: