manualshive.com logo in svg

HIKVISION DS-7608NI-I2/8P, Руководство пользователя, Страница: 211 / 221

Поделиться
Скачать
HIKVISION DS-7608NI-I2/8P Скачать руководство пользователя страница 211

I Series Network Video Recorder User Manual, 030117NA 

210 

Possible Reasons 

-  Poor network between NVR and IP camera, and there is packet loss during transmission. 

-  The frame rate has not reached the real-time frame rate. 

Steps 

1.

 

Verify the network between NVR and IP camera is connected. 

1)

 

When image freezes, connect the RS-232 ports on a PC and the rear panel of the NVR with a RS-232 
cable. 

2)

 

Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address 
may change according to the real condition), and check if there exists packet loss.

 

NOTE: 

Simultaneously press Ctrl and C to exit the ping command.

 

2.

 

Verify the frame rate is real-time frame rate (select “Menu > Record > Parameters > Record” and set the 
Frame rate to Full Frame). 

3.

 

Check if the fault is solved by the above steps. 

1)

 

If it is solved, finish the process. 

2)

 

If not, contact Hikvision tech support for further help. 

• 

Live view freezes when video is output remotely via Internet Explorer or platform software. 

Possible Reasons 

- 

Poor network between NVR and IP camera, and there exists packet loss during the transmission. 

- 

Poor network between NVR and PC, and there exists packet loss during the transmission. 

- 

The hardware performance is not good enough, including CPU, memory, etc. 

Steps 

1.

 

Verify the network between NVR and IP camera is connected. 

1)

 

When image is frozen, connect the RS-232 ports on a PC and the rear panel of the NVR with an 
RS-232 cable. 

2)

 

Open the Super Terminal, and execute the command of “

ping 

192.168.0.0

 –l 1472 –f

”

 

(the IP address 

may change according to the real condition), and check if there exists packet loss. 

NOTE: 

Simultaneously press Ctrl and C to exit the ping command.

 

2.

 

Verify the network between NVR and PC is connected. 

Содержание DS-7608NI-I2/8P






























































































































































































































Отзывы:

Нет отзывов