HIKVISION DS-7608NI-I2/8P Скачать руководство пользователя страница 177

Страница: 177 / 221

I Series Network Video Recorder User Manual, 030117NA

176

Figure 235 Set HDD Property

Set the HDD property to R/W, Read-only, or Redundancy.

Click the

button to save the settings and exit the interface.

In the HDD Information menu, the HDD property will be displayed in the list.

NOTE:

At least two hard disks must be installed in the NVR to set an HDD to Redundancy,
with one HDD with R/W property.

14.5

Configuring Quota Mode

Each camera can be configured with allocated quota for storing recorded files or captured pictures.

Enter the Storage Mode interface, Menu > HDD > Advanced.

Set the Mode to Quota, as shown in Figure 236.

NOTE:

Reboot the NVR to enable the changes.

Figure 236 Storage Mode Settings Interface

Select a camera for which you want to configure quota.

Enter the storage capacity in the Max. Record Capacity (GB) and Max. Picture Capacity (GB) text fields, as
shown in Figure 237.

Содержание DS-7608NI-I2/8P






























































































































































































































Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы:

HIKVISION DS-7608NI-I2/8P, Руководство пользователя, Страница: 177 / 221

Результаты поиска

Содержание DS-7608NI-I2/8P

Отзывы: