HIKVISION DS-7300HFI-S Series Скачать руководство пользователя страница 80

Страница: 80 / 98

Figure 2. HDD Group Settings Menu

Select OK to save and exit menu.

Note:

By default, all HDDs belong to group 1.

Setting

HDD

Status

You may change the behavior of your HDD by changing its status. The status of a HDD can be set to redundancy,
read-only or read/write (R/W).

Setting HDD to Read-Only

A HDD can be set to read-only to avoid important recorded files from being overwritten when the HDD becomes full.

To set a HDD to read-only:

Enter the HDD Management menu by clicking Menu > HDD.

Select HDD to protect.

Select the Property button to enter the Property Settings menu, as shown in Figure 3.

Figure 3. HDD Property Settings Menu

alarm shop

Содержание DS-7300HFI-S Series



































































































Результаты поиска

Содержание DS-7300HFI-S Series

Отзывы:

Похожие инструкции для DS-7300HFI-S Series

Бренды по названию

Популярные бренды

HIKVISION DS-7300HFI-S Series, Руководство пользователя

Результаты поиска

Содержание DS-7300HFI-S Series

Отзывы:

Похожие инструкции для DS-7300HFI-S Series

Бренды по названию

Популярные бренды