HIKVISION DS-7300HFI-S Series Скачать руководство пользователя страница 61

Страница: 61 / 98

If you would like to configure your own settings, enter the settings for:

• IP Address:

IP address you would like to use for your DVR.

• Subnet Mask:

Subnet Mask of network.

• Default Gateway:

IP address of your Gateway. Typically the IP address of your router.

• Preferred/Alternate DNS Server:

The preferred and alternate Domain Name System (DNS) Server

to be used with your DVR.

Click OK to save and exit the Network Settings menu.

Configuring

PPPoE

Settings

Your DVR also allows for Point-to-Point Protocol over Ethernet (PPPoE) access. To set up PPPoE access:

Enter the Network Settings menu by clicking Menu > Setting > Network.

Select the

General

tab.

Figure 3. Network Settings Menu

Select the

Advanced

tab. This will take you to the advanced network settings menu, shown in Figure

Figure 4. Advanced Network Settings

alarm shop

Содержание DS-7300HFI-S Series



































































































Результаты поиска

Содержание DS-7300HFI-S Series

Отзывы:

Похожие инструкции для DS-7300HFI-S Series

Бренды по названию

Популярные бренды

HIKVISION DS-7300HFI-S Series, Руководство пользователя

Результаты поиска

Содержание DS-7300HFI-S Series

Отзывы:

Похожие инструкции для DS-7300HFI-S Series

Бренды по названию

Популярные бренды