HIKVISION DS-7200-SH Скачать руководство пользователя страница 63

Страница: 63 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

4) Set the

Type

Motion

5) To schedule an all-day recording, check the checkbox after the

All Day

item.

Figure 5.17 Edit Schedule- All Day

6) To arrange other schedule, leave the

All Day

checkbox blank and set the Start/End time.

Note:

Up to 8 periods can be configured for each day. And the time periods can’t be overlapped

each other.

Repeat the above steps3)-6) to schedule motion detection triggered recording for all the week. If

the schedule can also be set to other days, click

Copy

Figure 5.18 Copy Schedule to Other Days

7) Click

to back to upper level menu.

If you can to copy the same schedule settings to other camera (s), click

Copy

to enter the Copy Camera

interface, and then select the camera (s) you want to copy.

Figure 5.19 Copy Schedule to Other Channels

5.4 Configuring Alarm Triggered Record

Note:

This section is available for DS-7224/7332-SH, DS-7300-SH and DS-8100-SH models only.

Purpose:

Follow the procedure to configure alarm triggered recording.

Содержание DS-7200-SH





























































































































































































Результаты поиска

Содержание DS-7200-SH

Отзывы:

HIKVISION DS-7200-SH, Руководство пользователя, Страница: 63 / 188

Результаты поиска

Содержание DS-7200-SH

Отзывы: