HIKVISION DS-7200-SH Скачать руководство пользователя страница 46

Страница: 46 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

4.1 Configuring PTZ Settings

Purpose:

Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done

before you control the PTZ camera.

Before you start:

Check that the PTZ and the device are connected properly through RS-485 interface.

Steps:

Enter the PTZ Settings interface.

Menu>Camera>PTZ>General

Figure 4.1 PTZ- General

Choose the camera for PTZ setting in the

Camera

dropdown list.

Enter the parameters of the PTZ camera.

Note:

All the parameters should be exactly the same as the PTZ camera parameters. Only PTZ Protocol

can be set for network cameras.

Example:

If the PTZ camera has a Baud rate as 115200, you should input 115200 in the Baud rate field.

Click

Copy

if you want to configure same settings to other PTZ cameras.

Click

Apply

button to save the settings.

4.2 Setting PTZ Presets, Patrols & Patterns

Before you start:

Please make sure that the presets, patrols and patterns should be supported by PTZ protocols.

4.2.1 Customizing Presets

Purpose:

Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes

place.

Steps:

Enter the PTZ Control interface.

Содержание DS-7200-SH





























































































































































































Результаты поиска

Содержание DS-7200-SH

Отзывы:

HIKVISION DS-7200-SH, Руководство пользователя, Страница: 46 / 188

Результаты поиска

Содержание DS-7200-SH

Отзывы: