HIKVISION DS-7200-SH Скачать руководство пользователя страница 39

Страница: 39 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

Instant Playback

Instant Playback only shows the record in last five minutes. If no record is found, it means there is no

record during the last five minutes.

Digital Zoom

Digital Zoom can zoom in the selected area to the full screen. You can left-click and draw to select the

area for zooming in, as shown in Figure 3.4.

Figure 3.4 Digital Zoom

Image Settings

Image Settings icon can be selected to enter the Image Settings menu.

Steps:

Set the period of a day for configuring independent image parameters so as to satisfy different light

conditions, e.g., daylight and night time. Two periods can be configured. When you have configured

Period 1, the Period 2 is remained as the

Other Time

Select the mode from the drop-down menu according to different light conditions.

Four modes are selectable:



Standard

: in general lighting conditions (default).



Indoor:

the image is relatively smoother.



Dim Light:

the image is smoother than the other three modes.



Outdoor:

the image is relatively clearer and sharper. The degree of contrast and saturation is high.

Содержание DS-7200-SH





























































































































































































Результаты поиска

Содержание DS-7200-SH

Отзывы:

HIKVISION DS-7200-SH, Руководство пользователя, Страница: 39 / 188

Результаты поиска

Содержание DS-7200-SH

Отзывы: