HIKVISION DS-7200-SH Скачать руководство пользователя страница 35

Страница: 35 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

3.1 Introduction of Live View

Live view shows you the video image getting from each camera in real time. The device automatically enters

Live View mode when powered on. It is also at the very top of the menu hierarchy, thus pressing the ESC

many times (depending on which menu you’re on) brings you to the Live View mode.

Live View Icons

In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the

record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are

alarms occur as soon as possible.

Table 3.1 Description of Live View Icons

Icons

Description

Alarm (video loss, tampering, motion detection or sensor alarm)

Record (manual record, schedule record, motion detection or alarm triggered record)

Alarm & Record

Содержание DS-7200-SH





























































































































































































Результаты поиска

Содержание DS-7200-SH

Отзывы:

HIKVISION DS-7200-SH, Руководство пользователя, Страница: 35 / 188

Результаты поиска

Содержание DS-7200-SH

Отзывы: