HIKVISION DS-7200-SH Скачать руководство пользователя страница 133

Страница: 133 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

131

Purpose:

You can use SNMP protocol to get device status and parameters related information.

Steps:

Enter the Network Settings interface.

Menu > Configuration > Network

Select the

SNMP

tab to enter the SNMP Settings interface.

Figure 9.18 SNMP Settings Interface

Check the

SNMP

checkbox to enable this feature.

Configure the SNMP settings.

Figure 9.19 Configure SNMP Settings

Click the

Apply

button to save and exit the interface.

Note:

Before setting the SNMP, please download the SNMP software and manage to receive the device

information via SNMP port. By setting the Trap Address, the device is allowed to send the alarm event and

exception message to the surveillance center.

9.2.5 Configuring UPnP™

Purpose:

UPnP™ can permits the device seamlessly discover the presence of other network devices on the network and

establish functional network services for data sharing, communications, etc. If you want to use the UPnP™

function to enable the fast connection of the device to the WAN via a router, you should configure the UPnP™

parameters of the device.

Before you start:

If you want to enable the UPnP™ function of the device, you must enable the UPnP™ function of the router

to which your device is connected. When the network working mode of the device is set as multi-address, the

Default Route of the device should be in the same network segment as that of the LAN IP address of the

router.

Steps:

Enter the Network Settings interface.

Содержание DS-7200-SH





























































































































































































Результаты поиска

Содержание DS-7200-SH

Отзывы:

HIKVISION DS-7200-SH, Руководство пользователя, Страница: 133 / 188

Результаты поиска

Содержание DS-7200-SH

Отзывы: