HIKVISION DS-7200-SH Скачать руководство пользователя страница 116

Страница: 116 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

114

8.2 Setting Sensor Alarms

Note:

This section is available for DS-7224/7232-SH, DS-7300-SH and DS-8100-SH models only.

Purpose:

You can set handling method of an external sensor alarm.

Steps:

Enter Alarm Settings interface and select an alarm input.

Menu> Configuration> Alarm

Figure 8.7 Alarm Status Interface

Select

Alarm Input

tab to enter Alarm Input Settings interface and set the handling method of the

selected alarm input.

Check

checkbox to enable the alarm input and click

to set up its alarm response actions.

Figure 8.8 Alarm Input Settings Interface

Select

Trigger Channel

tab and select one or more channels which will start to record or become

full-screen monitoring when an external alarm is input. Click

Apply

to save the settings.

Select

Arming Schedule

tab to set the channel’s arming schedule.

Choose one day of a week and up to eight time periods can be set within each day. Set up arming

schedule of other days of a week. You can also use

Copy

to copy an arming schedule to other days.

Click

Apply

to save the settings.

Note:

Time periods shall not be repeated or overlapped.

Select

Handling

tab to set alarm response actions of the alarm input (please refer to

Chapter 8.6

Содержание DS-7200-SH





























































































































































































Результаты поиска

Содержание DS-7200-SH

Отзывы:

HIKVISION DS-7200-SH, Руководство пользователя, Страница: 116 / 188

Результаты поиска

Содержание DS-7200-SH

Отзывы: