HIKVISION DS-2DF6236-CX Скачать руководство пользователя страница 69

Страница: 69 / 117

User Manual of Explosion-proof Dome

Click the PTZ control buttons to find the area you want to set the privacy mask.

Click

; drag the mouse in the live video window to draw the area.

You can drag the corners of the red rectangle area to draw a polygon mask.

Click

to finish drawing or click

to clear all of the areas you set without

saving them.

Click

to save the privacy mask, and it will be listed in the

Privacy Mask List

area; set

the value of

Active Zoom Ratio

on your demand, and then the mask will only appear when

the zoom ratio is greater than the predefined value.

Figure 5-32

Privacy Mask List

Check the checkbox of

Enable Privacy Mask

to enable this function.

5.4.6

Configuring Scheduled Tasks

Purpose:

You can configure the network speed dome to perform a certain action automatically in a
user-defined time period.

Steps:

Enter the Scheduled Task settings interface:

Configuration

PTZ

Scheduled Tasks

Figure 5-33

Configure Scheduled Tasks

Содержание DS-2DF6236-CX






















































































































Результаты поиска

Содержание DS-2DF6236-CX

Отзывы:

HIKVISION DS-2DF6236-CX, Руководство пользователя, Страница: 69 / 117

Результаты поиска

Содержание DS-2DF6236-CX

Отзывы: