HIKVISION DS-2DF6236-CX Скачать руководство пользователя страница 62

Страница: 62 / 117

User Manual of Explosion-proof Dome

Figure 5-25

Configuring Region Entrance Detection

Select the region from the dropdown list for detection settings.

Click the

button to start the region drawing.

Click on the live video to specify the four vertexes of the detection region, and right click to

complete drawing.

Repeat the step to configure other regions. You can click the

button to clear all

pre-defined regions.

Set the detection target for the region entrance detection.

You can select human, vehicle, or

all (human &vehicle) as the detection target from the dropdown list. If Human is selected,
only human beings will be identified as detection objects and as well as Vehicle.

Click

tab to enter the arming schedule setting interface. The time

schedule configuration is the same as the settings of the arming schedule for motion
detection. Refer to

Section

5.2.1 Configuring Motion Detection

Click

tab to select the linkage method taken for the video loss alarm,

Notify surveillance center, send email, upload to FTP, trigger channel, smart tracking and
trigger alarm output are selectable. Refer to

Section

5.2.1 Configuring Motion Detection

Click

to save the settings.

5.3.6

Configuring Region Exiting Detection

Purpose:

Region exiting detection function detects people, vehicle or other objects which exit from a

pre-defined virtual region, and some certain actions can be taken when the alarm is triggered.

Содержание DS-2DF6236-CX






















































































































Результаты поиска

Содержание DS-2DF6236-CX

Отзывы:

HIKVISION DS-2DF6236-CX, Руководство пользователя, Страница: 62 / 117

Результаты поиска

Содержание DS-2DF6236-CX

Отзывы: