HIKVISION 607 Series Скачать руководство пользователя страница 116

Страница: 116 / 163

607 Series Face Recognition Terminal

User Manual

106

(Optional) You can click Delete button to delete the selected time period or click Clear button
to delete all the configured time periods.

(Optional) Click Copy to button to copy the settings to other card readers.

Click Save button to save parameters.

7.8.3

Multiple Authentication

Purpose:
You can manage the cards by group and set the authentication for multiple cards for one access
control point (door).

Note:

Please set the card permission and apply the permission setting to the access control device

first. For details, refer to Chapter 7.7 Permission Configuration.
Steps:
1.

Click Multiple Authentication tab to enter the following interface.

Select access control device from the list on the left.

Содержание 607 Series




































































































































































Результаты поиска

Содержание 607 Series

Отзывы:

HIKVISION 607 Series, Руководство пользователя, Страница: 116 / 163

Результаты поиска

Содержание 607 Series

Отзывы: