HIKVISION 114-029 Скачать руководство пользователя страница 85

Страница: 85 / 190

Network Camera User Manual

Settings > QoS

QoS Settings

Configure the QoS settings, including Video/Audio DSCP, Event/Alarm DSCP

and Management DSCP.

The valid value range of the DSCP is 0 to 63. The bigger the DSCP value is, the

higher the priority is.

Note:

DSCP refers to the Differentiated Service Code Point; and the DSCP value

is used in the IP header to indicate the priority of the data.

Click

Save

to save the settings.

Note:

A reboot is required for the settings to take effect.

Configuring 802.1X Settings

Purpose:

The IEEE 802.1X standard is supported by the network cameras, and when the feature

is enabled, the camera data is secured and user authentication is needed when

connecting the camera to the network protected by the IEEE 802.1X.

Before you start:

The authentication server must be configured. Please apply and register a user name

and password for 802.1X in the server.



For your privacy and to better protect your system against security risks, we

strongly recommend the use of strong passwords for all functions and network

devices. The password should be something of your own choosing (using a

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 85 / 190

Результаты поиска

Содержание 114-029

Отзывы: