HIKVISION 114-029 Скачать руководство пользователя страница 67

Страница: 67 / 190

Network Camera User Manual

multicast group address. Before utilizing this function, you have to enable the

Multicast function of your router.



A reboot is required for the settings to take effect.

Configuring DDNS Settings

Purpose:

If your camera is set to use PPPoE as its default network connection, you can use the

Dynamic DNS (DDNS) for network access.

Before you start:

Registration on the DDNS server is required before configuring the DDNS settings of

the camera.

Steps:

Enter the DDNS Settings interface:

Configuration > Network > Basic Settings >

DDNS

Check the

Enable

DDNS

checkbox to enable this feature.

Select

DDNS Type

. Two DDNS types are selectable: DynDNS and NO-IP.



DynDNS:

Steps:

(1)

Enter

Server Address

of DynDNS (e.g. members.dyndns.org).

(2)

In the

Domain

text field, enter the domain name obtained from the DynDNS

website.

(3)

Enter the

User Name

and

Password

registered on the DynDNS website.

(4)

Click

Save

to save the settings.

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 67 / 190

Результаты поиска

Содержание 114-029

Отзывы: