HIKVISION 114-029 Скачать руководство пользователя страница 54

Страница: 54 / 190

Network Camera User Manual

Set the log search conditions to specify the search, including the Major Type,

Minor Type, Start Time and End Time.

Click

Search

to search log files. The matched log files will be displayed on the

log list

interface.

Log Searching

To export the log files, click

Export

to save the log files.

System Service

Purpose:

System service settings refer to the hardware service the camera supports. Supported

functions vary according to the different cameras. For the cameras support IR Light,

ABF (Auto Back Focus), Auto Defog, or Status LED, you can select to enable or

disable the corresponding service according to the actual demands.

ABF:

When ABF function is enabled, you can click

on PTZ control panel to

realize auxiliary focus.

Third Stream

: For some models, third stream is not enabled by default. Check

Enable Third Stream

to enable the function.

Содержание 114-029































































































































































































Результаты поиска

Содержание 114-029

Отзывы:

HIKVISION 114-029, Руководство пользователя, Страница: 54 / 190

Результаты поиска

Содержание 114-029

Отзывы: