HIKOKI NT 65MA4, Инструкция по эксплуатации

Страница: 11 / 56

11
English
Removing the nails:
Depress the nail feeder (A) slightly and slowly slide the
nail feeder (B) forward.
Remove the nails from the nailer.
CAUTION
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a work
bench on fl oor. Also, never face the nail outlet toward
any part of a person.
HOW TO USE THE NAILER
CAUTION
○ Do not use the body or any portion of the tool as a
hammer as nails may be discharged unexpectedly or
the tool may become damaged and serious injury could
occur.
○ Take precautions to ensure the safety of persons in the
vicinity during operation.
○ Ensure tool is always safely engaged on the workpiece
and cannot slip.
○ Never carry a pneumatic tool by its hose.
○ Never drag a pneumatic tool by its hose.
1. Nailing procedures
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use SINGLE SEQUENTIAL ACTUATION MECHANISM
or CONTACT ACTUATION MECHANISM in accordance
with the work to be performed.
(1) Intermittent nailing
Set the switching device to the upward position (to set
to SINGLE SEQUENTIAL ACTUATION MECHANISM)
(See
Fig. 3
).
Depress the nail outlet onto the desired point; then
pull the trigger to drive a nail in a single shot (See
Fig. 5
).
After nailing once, nailing will not be possible again until
the trigger is released and pressed again.
WARNING
A nail will fi re each time the trigger is depressed as long
as the push lever remains depressed.
CAUTION
If you do not pull the trigger quickly and crisply while in
the single shot mode, the nailer will bounce and shoot
several nails instead of just one. To avoid this, be sure
to pull the trigger quickly and crisply.
(2) Push lever
When depressing the nail outlet, be sure to fully lift the
push lever (See
Fig. 5
) to release the safety lock. Thus,
nails cannot be driven without releasing the safety lock
even though the trigger is pulled.
(3) Continuous nailing
Set the switching device to the downward position (to
set to CONTACT ACTUATION MECHANISM) (See
Fig. 6
).
First, pull the trigger. Then depress the devise onto
the desired position to automatically drive nails (See
Fig. 7
).
The SINGLE SEQUENTIAL ACTUATION MECHANISM is
for use where precision fastener placement is desired.
The SINGLE SEQUENTIAL ACTUATION MECHANISM
may reduce the possibility of bodily injury to you or others
in the work area compared to the CONTACT ACTUATION
MECHANISM.
This is because it is less likely to drive
an unwanted nail if you keep the trigger pulled and
accidentally bump the push lever against yourself or
others.
The SINGLE SEQUENTIAL ACTUATION MECHANISM
may also reduce the speed of operation compared to
the CONTACT ACTUATION MECHANISM. The SINGLE
SEQUENTIAL ACTUATION MECHANISM is recommended
to inexperienced users.
CAUTION
○ Exercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
○ Do not drive a nail on another nail.
○ Do not drive a nail on metal parts.
NOTE
○ Precautions on no-load operation
Sometimes nailing will continue after driving in all nails
previously contained in the magazine.
This is termed “no-load operation”. Such operation may
deteriorate the damper, magazine, and nail feeder.
To avoid no-load operation, occasionally con fi rm the
amount of remaining nails. On the other hand, all nails
should be removed after using this nailer.
○ Always handle nails and package carefully. If nails are
dropped, collating bond may be broken.
○ After nailing:
(1) disconnect air hose from the nailer;
(2) remove all nails from the nailer;
(3) supply 5 – 10 drops of HiKOKI pneumatic tool
lubricant into the air plug on the nailer; and
(4) open the petcock on the air compressor tank to
drain any moisture.
2. Adjusting the nailing depth (See Fig. 8)
To assure that each nail penetrates to the same depth,
be sure that:
(1) the air pressure to the nailer remains constant
(regulator is installed and working properly), and
(2) the nailer is always held fi rmly against the
workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
DISCONNECT AIR HOSE FROM NAILER.
If nails are driven too deep, turn the adjuster to the
shallow side.
If nails are driven too shallow, turn the adjuster to
the deep side.
Stop turning the adjuster when a suitable position is
reached for a nailing test.
Connect the air hose.
ALWAYS WEAR EYE PROTECTOR.
Perform a nailing test.
DISCONNECT AIR HOSE FROM NAILER.
Choose a suitable position for the adjuster.
3. Using the blow nozzle
CAUTION
○ Be sure to release your fi nger from the trigger before
using the blow nozzle.
○ Do not point the air outlet at a person.
○ Do not use the blow nozzle with the push lever left fi t.
This Nailer has a blow nozzle that blows out wood shavings
which occur during work.
Press the knob with your thumb to use the blow nozzle
(See
Fig. 9
).
NOTE
○ When the blow nozzle is used for a long time, the nailing
force may degrade temporarily. In this case, allows the
air supply pressure to stabilize before starting work.
○ Oil in the body or drained water from the compressor can
sometimes spout out of the air outlet. It is recommended
that you once conduct a test before use and see if
such phenomenon happens at an environment where
spouted oil will cause any inconvenience.
000Book̲NT65MA4(S).indb 11 000Book̲NT65MA4(S).indb 11 2019/08/13 10:38:36 2019/08/13 10:38:36