background image

L

IN

E

 IN

P

U

T

--

-B

A

L

A

N

C

E

D

--

-S

U

B

S

O

N

IC

--

-B

A

S

S

 E

Q

--

-R

E

M

O

T

E

--

-L

O

W
 P

A

S

S

--

-P

H

A

S

E

--

-L

E

V

E

L

--

-P

O

W
E

R

--

-L

IN

E

 O

U

T

P

R

O

TE

C

T

LC

H

R

C

H

L

R

1

5

H

   

3

5

H

  0

d

B

   

  1

8

d

b

   

   

   

   

   

   

3

5

H

 2

5

0

H

 0

   

   

 1

8

0

   

9

V

   

   

0

.2

V

   

   

   

   

   

   

IN

P

U

T

POWER

PROTECT

HIFONICS

HIFONICS

0dB

18dB

HFR-1

HFR-1

Connect RCA cable from
head-unit with RCA  input
(LINE INPUT). 

If you use more than one 
subwoofer you can optionally 
use Channel two

Minimum impendance 
not under 1 Ohm

10

Monoblock-Amplifier - Applications

BXi 750 / BXi 1100

 

D / BXi 1600

 

D

Caution

Be careful not to connect speaker (-) to the ground or vehicle chassis.

Interconnect cable checklist:

• Connect the LINE INPUT of the amplifier to the head unit line output with good quality RCA to RCA cables.
• Connect the speakers with the terminal block (SPEAKER OUTPUT/ - LEFT + and - RIGHT +) of the amplifier.
• The minimum final speaker impedance must not be below 2 Ohm per channel. Too low speaker loads result in too high 

heat dissipation and may cause the amplifier run into protection.

• Please observe speaker channel and polarity as printed by the speaker terminal block. Incorrect phasing of the speakers 

results in total loss of bass response.

• 

• 

INPUT LEVEL

• Turn the INPUT LEVEL control on the amplifier to 5V position.
• Turn the head unit volume control to about 80-90% of its full setting.
• Turn the INPUT LEVEL control clockwise until you hear some distortion.
• Then turn back the INPUT LEVEL control slightly until you can hear clean sound.

Low pass

• This eliminates the higher frequencies. Set the crossover-frequency between 50Hz-100Hz, depending on the size of the 

installed speakers.

Subsonic

• This eliminates the lowest frequencies and protects the speakers from damage.

Bass EQ

• Allows you to adjust the bass boost from 0dB up to 18dB 

Caution!

 Please use the Bass-Boost carefully. The additional boost may result in clipping or overload.

Phase

• This allows you to match the Phase  0° to 180°. So you can integrate each subwoofer.

• 

Connection for remote 
control to adjust subwoofer 
from your seat.

Содержание Brutus BXi750













Отзывы: