HIAB K-HiPro 285-425-4 Series Скачать руководство пользователя страница 89

Страница: 89 / 114

8.3.1. Daily inspection

Refer to the daily inspection checklist at the end of this manual to photocopy.

Presence of signs and symbols

• See chapter "Safety precautions and warnings" under section "Signs on the crane". Make sure

that all the signs shown in section "Signs on the crane" are in position and in good conditions .

• Make sure that all the symbols on your crane are in good conditions.

Locking devices

• Make sure that the locking devices are undamaged and working properly.
• Make sure that the locking devices are properly locked.

Shafts, shaft lockings, bearings and bushings

• Check that the shafts, shaft lockings, bearings and bushings are undamaged and working

properly.

Stop buttons

• Check that the Stop buttons are undamaged and working properly.

Levers

• Check that the levers operate smoothly.
• Check that the levers return to neutral position.

Controller

• Do a check of the controller functionality.

Crane structure

• Check for damage to the crane structure (e.g. any formation of cracks).

DANGER

In the event of damage that presents a safety risk:
• Do not use the crane.
• Have the damage repaired immediately by a HIAB service workshop.

Maintenance and Service

HIAB K-HiPro 285-425 X4

Содержание K-HiPro 285-425-4 Series



















































































































Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды

HIAB K-HiPro 285-425-4 Series, Руководство оператора

Результаты поиска

Содержание K-HiPro 285-425-4 Series

Отзывы:

Похожие инструкции для K-HiPro 285-425-4 Series

Бренды по названию

Популярные бренды